AUTONET TV

U and your U-Joints (Lubricate U-Joints)

If your vehicle’s power goes to the rear wheels, then you have something called U-joints in the drivetrain. U-joints are connectors that allow the rotating power from your vehicle’s engine to deliver its power through a driveshaft to make the rear wheels rotate.  You need U-joints because the surfaces you drive on aren’t perfectly flat, and the driveshaft has to allow for some flexibility when you are traveling over uneven surfaces.

As you can imagine, the U-joints have to move and flex a lot as your vehicle is going down the road.  They have bearings in them to allow that flexibility, and those bearings are lubricated when your vehicle is made.  Some U-joints have lifetime lubrication and are not designed to be serviced.  When they fail, they have to be replaced.  Others have grease fittings on them that need periodic lubricating by a technician at intervals recommended by your vehicle’s manufacturer. 

There are signs you can look for that your U-joints need attention.  You may hear a clunk when the gears shift into drive or reverse.  You may feel your vehicle vibrate as you move down the road.  Other signs are leaks at the back of your transmission or a banging sound right before you lose power.  Sometimes, though, if you wait until you notice these symptoms, the U-joints may already be damaged.  

That’s why it’s important that your vehicle’s U-joints be periodically inspected and lubricated.  At the same time, a technician should thoroughly inspect the driveshaft and other connected components.  

Keep your U-joints in good shape, and both of U will continue to enjoy years of reliable transportation.

L and M Motors Inc
400 W 53rd Ave
Anchorage, AK 99518
907-563-4994

Braking Good (Brake Drum Replacement)

Maybe your vehicle feels like Breaking Bad.  In other words, when you brake, things are bad.  You may find it takes you a longer distance to stop, you feel a vibration, or it’s pulsating when you depress the brake pedal, or perhaps your vehicle pulls to one side.

Those can be symptoms of failing brake drums.  While a lot more vehicles these days have disc brakes, many vehicles still have brake drums, almost always in the rear wheels. The drum is a cast iron shallow cylinder that surrounds the other parts, including curved brake shoes that press pads against the drum to slow you down or stop the vehicle.

Any time you have things going wrong with your brakes, you should get them fixed soon.  Safely operating any vehicle depends on having the brakes be able to slow and stop you dependably.  It can make the difference between avoiding a collision and having one. 

When you bring your vehicle in, a technician will inspect your braking system. Depending on the wear, drum brakes can be resurfaced or replaced. Sometimes it’s cheaper to replace the drum than to resurface it.  It’s important for all the other brake system components to be inspected first and all worn parts replaced.  

Most of the time, when you have your drums resurfaced or replaced, the brake shoes should be replaced at the same time. You have brakes at each end of your axles, and the same brake service should be done at both ends so that both sides can have consistent, even stopping power. 

Your brakes can save your life.  If their braking power is bad, you owe it to yourself and others on the road to let us help make them good again.  Good and safe.

L and M Motors Inc
400 W 53rd Ave
Anchorage, AK 99518
907-563-4994

Flat Tire? Three?s the Charm (Tire Repair)

For most drivers, at some point you’re going to have a flat tire. Depending on how it was damaged, it may have to be replaced.  But sometimes, a repair will do the trick, as long as the puncture isn’t on the sidewall and the hole is smaller than ¼ inch/6.35mm in diameter. Here are the three common ways your tire can be fixed.

One way is to put a plug in the hole.  Since most tires are damaged by running over sharp objects such as screws and nails, the small hole from which the air is escaping is on the part of the tire that touches the road. If it’s in the sidewall, it most likely can’t be fixed.  

In the plug method, a technician inserets a rubber plug.  It is covered with some sticky, gluey stuff, and is pushed into the hole from the outside. That plugs the hole and stays in place, thanks to the glue. Friction from driving heats it up and seals the deal.  

Another method is to patch the hole.  For this, your tire has to first be taken off the vehicle, then off the rim so the technician can get access to the inside. There, they’ll clean the inside surface around the hole and apply a rubber patch with an adhesive on it. This type of patch works well, and because of the extra steps and complexity, costs more than having your tire plugged.  

There’s also a combination of those methods just described, the plug-patch.  It is, in essence, a type of patch with glue on it that has a plug sticking out of it.  The plug is inserted into the tire from the inside and pulled through the hole from the outside, drawing the attached patch tight against the tire’s inside surface. The last two methods can’t be used if the hole is near another repair or the sidewall.    

The good news is if it’s fixed properly, your repaired tire should give you good service.

L and M Motors Inc
400 W 53rd Ave
Anchorage, AK 99518
907-563-4994

No Fueling Around (Fuel Filter Replacement)

A driver called in to the shop the other day saying his European sports sedan had an odd problem.  He was driving when his car started to slow down.  Applying more throttle didn't help.  He pulled over to the side of the road, shut the engine off and waited a few minutes before starting it up again.  It ran fine… for a couple of minutes.  Then the same thing happened.  He was able to finally get home by stopping and restarting, and he was calling to see if we could take a look at it. 

Turned out it was one of his car's fuel filters that choked up with debris so badly that enough fuel couldn't get through it.  When he stopped the car, enough fuel could flow through the unpressurized fuel line to supply enough fuel for a couple of minutes when he restarted his car. But then the pressure would cause things to clog again.  

There are other symptoms that point to a failing fuel filter. Perhaps your engine misfires, your vehicle is hard to start, or your fuel pump starts making odd noises. 
If you experience any of these signs, bring your vehicle in so we can have a technician check it out. 

Many vehicles have at least two fuel filters. One is a strainer that is part of the fuel pump in the fuel tank, and the other is in the main fuel line. Your vehicle's manufacturer recommends how often yours should be changed, but your driving habits and environment (such as dirty or dusty conditions) may mean yours will have to be replaced more often.  

The technician will also look to see if your vehicle might have another problem that's causing your fuel filter to fail more frequently than normal, such as corrosion in the fuel tank. 

Your engine needs fuel to run. Maintain the health of your fuel system and that will help keep you on the road to your destination.

L and M Motors Inc
400 W 53rd Ave
Anchorage, AK 99518
907-563-4994